Now there are two types of solar terms that we commonly have，One is an electronic festive door，Another is the pull -line mechanical festival.。We will discuss separately。
The picture above is the structural diagram of an electronic fracture door。Electronic festivals have no idle motor，Under idling conditions, the computer controls the flipping of the throttle and turns a small angle to let the air flow pass，Provide the amount of intake required for idle speed。So we know that the gap formed by the electronic festivation door after turning a small angle through the flipping plate provides an air volume required for idle speed。Electronic festivals will have dirt attachment at the seam of the flip and the inner wall of the throttle after a period of time.，The intake channel is very small under idling conditions，After being blocked by dirt, it will cause a reduction in air volume。At this time, the computer will automatically adjust the computer，Increases the volume through the increase of rotation angle by controlling the overturn。But this cannot solve the fundamental problem。At this time, you need to clean the throttle。The intake channel is unblocked after cleaning，Some people think that it needs to be matched，In fact, most models do not need to be matched，Just open it。After a period of time, the computer will adjust the computer itself。When you step on the accelerator pedal during normal driving process, the overturn will turn the corresponding angle according to the signal of the pedal。At this time, even if the firing is dirty，The dirt dirt does not affect normal air intake。So some friends feel that the vehicle power is better after cleaning the throttle.。Because those dirt only affects idle state。Unless the solar terms are dirty and half of the section are blocked。But in reality is impossible。Let's take Seabeta look at the ordinary pull -line throttle.Line -line throttle is an idle motor and bypassing room。The air under the bypassing room enters the engine under idling.，Provide the amount of intake required for idle speed。The idle motor controls the amount of air intake by controlling the movement of the valve core to achieve the precise control of the computer's idle。The picture above indicates the path of air in idle state。It can be seen that the air enters the engine through the bypass chamber。Therefore, even if there is dirt at the combination of flip and inner walls, it will not affect idle speeds。So if your car is a pull -line throttle，You see that the inner wall of the throttle is very dirty，No need to worry，No impact at all。Because the air does not pass here during idling。and when driving normally，It will not have much impact on the air intake。but not to say，It is also possible to gather some dirt in the bybeling room under certain conditions，It affects the control of idling motors，At this time, it also needs to be cleaned。But the sheltering room was cleaned。Some friends said: My car is a pull -line throttle，The idle speed is fine after cleaning。This is likely to be cleaned up by the bypass room by the way when cleaning。Summary:1、Vehicles with electronic festivals need to be cleaned regularly。2、Vehicles of the pull -line throttle need to focus。Reasonable carThe throttle is too dirty will bring a lot of problems，If the idle is unstable、Speed speed and low、The vehicle frustration when accelerating or receiving oil、Stallout, etc.。If there is too much dirt in the throttle slime，It may cause the engine to accelerate，Increase fuel consumption，It is a big trouble for the owners，So what should I do if the solar terms are dirty? Very simple，Clean it，Go to the 4S shop or professional repair shop to complete，Do you have to go to the 4S shop every time you clean it? Actually don't use，You can solve it by yourself，Just in the end, you need to initialize it，That is the reset that is usually said。
seabet io
Disassembling at the throttle door、Installation，seabet mySkilled and stable operations can avoid damage to the throw valve body。A total of several parts needed to be moved by disassembling the throw valve body:1. The engine cover plate,2. The end and spring card3. The intake tract throwing valve end and spring card,4. Calcidal box ventilation pipes solenoid valve plug5. Castle shaft box ventilation pipe bypass pipe7. The throw valve cable beam plug8. Capsule valve water circulation tube9. The throttle line10. Fixed screws of the throttle valveUse the right tools to use these parts、Active operation of the right force，The probability of damage is very small。and most of the damage of the throw valve body itself is internal circuits and idle motors。When cleaning the festival valve，First of all, remove the intake throat，Display thrilling door，Disassemble the battery's negative electrode，Turn off the ignition switch，Straighten the throttle flipplace，Spray a small quantized clearing agent in the throttle，Then carefully scrub with polyester rag，Deep of the throttle，You can clamp the rag with a clip with a clip with a clip.。After the throttle is cleaned，Put it in the program just disassembled。
How to initialize the throttle?
After cleaning the firing door and installation and reset，Then you can start initialization。The reason why it is initialized，It is because when the computer adjusts the openness of the firing door，Is a memory function，Because of the blockage of sludge，To ensure the amount of air intake，Computing opportunities to automatically adjust the opening of the firing door，Let the air intake be in normal state。Actually，Initialization is also very simple，You can do it through a dedicated computer，You can do it hand -made without a dedicated computer，But do no computer quickly，and sometimes it may fail，Need to do it again。Different models of divided shares have different methods:1、Open the key second，is the gear of the full light of the instrument indicator，After waiting for 20s，Step on the accelerator to the end，Keep about 10S，pine pipe，Turn off the ignition switch，Pull seabet appout the key，Initialization is completed。
2、Open the key second，Keep 30S，Then turn off the ignition switch，Just pull out the key。You need to note that it is，After the two methods are done，Wait for a while，can try to get angry，Generally, wait 15-20s，Then fire，See if the refueling is normal，Whether the engine fault light goes off，If unsuccessful at a time，Just do the second time，until successful，Generally successful。3、Some models must complete the initialization through the computer，If you belong to the vehicle, you have to go to a shop with computer reset.。
Official Weibo